模型:IKPD-20系列,en	 
筆記:	Universal AC input/ Full range
High Efficiency, and High reliability
Ultra-miniature size, low profile
Output protections: OLP/OVP/SCP
Wide operating ambient temperature (-25℃~70℃)
All using 105℃ long life electrolytic capacitors.
100% full load burn-in test
| MODEL | IKPD-20-3.3 | IKPD-20-5 | IKPD-20-12 | IKPD-20-15 | IKPD-20-24 | IKPD-20-48 | ||
| OUTPUT | DC Output | 3.3V | 5V | 12V | 15V | 24V | 48V | |
| Rated Current | 4一個 | 4一個 | 1.67一個 | 1.34一個 | 0.84一個 | 0.42一個 | ||
| CurrentRange Note 1 | 0~4A | 0~4A | 0~1.67A | 0~1.34A | 0~0.84A | 0~0.42A | ||
| Ripple and Noise Note 2 | 0~60℃ | <50mV | <50mV | <50mV | <50mV | <50mV | <100mV | |
| -20~0℃ | <75mV | <75mV | <75mV | <75mV | <75mV | <100mV | ||
| Voltage ADJ. Range | 3.1~3.6V | 4.4~5.6V | 11.1~13.1V | 13.7~16.1V | 22.0~25.4V | 45.6~50.4V | ||
| Voltage Accuracy | ±2.0% | ±2.0% | ±2.0% | ±2.0% | ±2.0% | ±2.0% | ||
| 線路調整 | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ||
| 負載調節 | ±2.0% | ±2.0% | ±2.0% | ±2.0% | ±2.0% | ±2.0% | ||
| Set-up Time | <2.0S (115Vac input, Full load); <1.0S (230Vac input, Full load) | |||||||
| Hold up Time | >10mS(115Vac input, Full load); >20mS(230Vac input, Full load) | |||||||
| Temperature Coefficient | ±0.03%/℃ | |||||||
| Overshoot and Undershoot | <5.0% | |||||||
| INPUT | VoltageRange | 85Vac~264Vac,120Vdc~370Vdc | ||||||
| FrequencyRange | 47Hz~63Hz | |||||||
| Efficiency ( Typical) | 115Vacinput | 69% | 76% | 79% | 80% | 80% | 80% | |
| 230Vacinput | 68% | 75% | 78% | 79% | 79% | 79% | ||
| AC Current (最大。) | 0.4一個 | 0.5 | 0.5一個 | 0.5一個 | 0.5一個 | 0.5一個 | ||
| Inrush Current (Typical) | Cold start 20A@115Vac 40A@230Vac | |||||||
| Leakage Current | Input—output:<0.35mA Input—PG:<0.75mA | |||||||
| PROTECTION | Over Load | 105%~150% rated output power; Hiccup mode, auto recovery | ||||||
| Over Voltage | 110%~140% of rated output voltage, Constant Voltage. | |||||||
| Short Circuit | Long-term mode, auto recovery | |||||||
| ENVIRONMENT | Operating amb. Temp. & Hum. | -25℃~70℃; 20%~90%RH No condensing(refer to the derating curve) | ||||||
| Storage Temp. & Hum. | -40℃~85℃; 10%~95%RH No condensing | |||||||
| SAFETY & EMC Note 3 | Safety Standards | UL60950-1; EN60950-1:2006 | ||||||
| Withstand Voltage | Primary-Secondary:3.0KVa;≤10mA .Primary-PG:1.5KVac;≤10mA. Secondary-PG:0.5KVDC;≤10mA. | |||||||
| Isolation Resistance | ≥100M ohms | |||||||
| EMI Conduction&Radiation | Compliance to EN55022(CISPR22)ClassB | |||||||
| Harmonic Current | Compliance to EN61000-3-2,17625.1-2003 | |||||||
| EMSImmunity | Compliance to EN61000-4-2,3,4,5,6,8,11;ENV50204,light industry level,criteriaA | |||||||
| OTHERS | MTBF (MIL-HDBK-217F) | More than 200,000Hrs (25℃, Full load) | ||||||
| Dimension (L*W*H) | 89×51×20mm | |||||||
| Packing | ||||||||
| Cooling method | Cooling by free air convection | |||||||
| NOTE | 1.All parameters NOT specially mentioned are measured at rated input, rated load and 25℃ of ambient temperature. 2.Measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1 uF & 47uF parallel capacitor. 3. The power supply is considered as a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. | |||||||
